ISO 14644-1 is the international standard that classifies cleanrooms and clean zones by how many airborne particles a cubic metre of air may contain. It replaced US Federal Standard 209E, which was withdrawn in 2001, but the old names such as Class 100 and Class 10,000 still turn up in specifications, drawings and conversations. Knowing how the two systems line up, and what a class does and does not tell you, prevents expensive misunderstandings at the design stage.
How the class numbers work
An ISO class runs from ISO 1, the cleanest, to ISO 9, which is close to ordinary indoor air. Each step is a tenfold change: an ISO 7 room may hold ten times as many particles as an ISO 6 room, and a tenth as many as an ISO 8 room. The standard derives every limit from one formula based on the class number and the particle size, so the allowed count falls steeply as particle size increases.
Most specifications quote the 0.5 µm column, the size most people work with:
| ISO class | Max particles 0.5 µm and larger per m³ | Former FS 209E name | Typical uses |
|---|---|---|---|
| ISO 5 | 3,520 | Class 100 | Critical zones under unidirectional flow, inside clean benches and isolators |
| ISO 6 | 35,200 | Class 1,000 | Some electronics, optics and precision assembly |
| ISO 7 | 352,000 | Class 10,000 | Compounding buffer rooms, many medical device rooms |
| ISO 8 | 3,520,000 | Class 100,000 | Anterooms, gowning, packaging and support areas |
| ISO 9 | 35,200,000 | none | Rarely specified; close to room air |
The old Federal Standard counted particles per cubic foot, which is why 3,520 per cubic metre lines up with roughly 100 per cubic foot. The match is close, not exact, so write new specifications in ISO terms.
A classification also names the particle sizes considered. A room can be specified as ISO 7 at 0.5 µm and 5 µm, and the certifier then counts both channels. The 2015 edition of the standard does not set 5 µm limits for ISO 5 and cleaner, because counts that low cannot be sampled reliably. GMP Annex 1 handles larger particles in its own tables, covered in our guide to GMP grades A to D.
Occupancy states matter as much as the class
ISO 14644-1 recognizes three occupancy states:
- As-built: the room is complete and running, with no production equipment and no people.
- At-rest: equipment is installed and running as agreed, with no personnel present.
- Operational: the room is working as intended, with the agreed number of people and processes running.
People are the largest particle source in most cleanrooms, so the same room can test one or more classes cleaner at rest than in operation. A specification that says only "ISO 7" leaves the most important question open. Write the state into the contract, for example "ISO 7 operational with four gowned staff and the filling line running", so the HVAC engineer, the builder and the certifier design and test to the same condition.
How a room is classified
Classification is a measurement, not a design claim. Under the 2015 edition:
- The number of sampling locations comes from a table in the standard based on floor area, with locations spread across the room.
- At each location the counter samples enough air to expect at least 20 particles at the class limit for the largest particle size considered, with a minimum of 2 litres and at least one minute per location.
- Every location must meet the limit on its own. The statistical allowance across locations used in the 1999 edition was dropped.
The particle counters must be calibrated, and the report should list instrument serial numbers and calibration dates. ISO 14644-1 covers airborne particles only. It says nothing about microorganisms, surface contamination, temperature or pressure. Those come from other parts of the ISO 14644 series, from GMP, or from USP <797> for compounding. Our guide to certification and monitoring explains how classification fits with routine testing.
Choosing the right class
Start from the process, not from a class number. Ask which particle sizes damage the product, whether viable organisms are the real concern, and which regulator or customer sets the requirement. A medical device assembler may need ISO 7 or ISO 8 by contract. A sterile compounding pharmacy has its classes set by USP <797> and the NAPRA model standards. A semiconductor fab may need ISO 4 or cleaner inside the process tool and ISO 6 or 7 in the surrounding bay; the electronics cleanroom overview shows how that zoning typically works.
Every step cleaner raises the supply air volume, the number of HEPA filters, fan energy, and the discipline needed for gowning and cleaning. That is why the cleanest zones are usually kept small. An ISO 5 clean bench or PCR workstation inside an ISO 7 room can protect a critical step at a fraction of the cost of making the whole room ISO 5. The HVAC and air change guide shows how the class drives airflow and equipment size.
Planning tips
- Specify the class, the occupancy state and the particle sizes together, in writing.
- Use ISO terms in new documents, and translate legacy "Class 10,000" language once, at the start of the project.
- Put the cleanest work into the smallest practical zone.
- Size air handling for the class you need now plus any upgrade your process roadmap actually supports; capacity for a class you never use is expensive to build and to run.
- Agree before construction ends who will certify the room, in which occupancy state, and against which edition of the standard.
If you are unsure which class your process needs, a consultation can help you map process steps to zones before anything is drawn.


